Updated November 2026
Knowing how to clean a Levoit air purifier filter comes down to one key fact: only some of the filters in these units can be cleaned, and the rest must be replaced. This guide shows you how to tell which type you have, how to clean a washable pre-filter, and how to avoid damaging the parts that actually trap fine particles.
First, Identify Your Filter Type
Most Levoit purifiers use a layered filter assembly, usually a pre-filter wrapped around a True HEPA filter and sometimes an activated carbon layer. The outer mesh pre-filter catches hair, lint and larger dust, and it is the only layer most owners can clean. The HEPA and carbon layers are not designed to be washed or vacuumed. Water, compressed air and brushes can tear the HEPA media or strip the carbon, and once that happens the filter no longer performs to its rating.
Shopping for one? See our guide: Levoit Air Purifier Filter Review (2026): Replacement Options, Pros and Cons.
Check the filter packaging or the manual for your model number. If the manual says the pre-filter is washable, you can clean it. If it lists only replacement intervals, plan to swap the whole cartridge.
How to Clean the Pre-Filter Step by Step
Cleaning the pre-filter takes about ten minutes and should be done every few weeks in homes with pets or heavy dust. Manufacturers typically recommend a gentle approach:
- Unplug the purifier and wait until it is fully stopped.
- Open the filter access door on the back or bottom, depending on your model, and remove the filter cartridge.
- Remove the outer pre-filter mesh from the cartridge if it is designed to come off. Do not pull the HEPA layer out with it.
- Vacuum the mesh with a soft brush attachment on low suction to lift hair and loose dust.
- Rinse the mesh under lukewarm running water. Work from the inside out so particles push away from the surface.
- Let it air-dry completely on a towel for at least 24 hours. Do not use heat, a hair dryer or direct sunlight.
- Reattach the pre-filter, reinsert the cartridge, close the door and plug the unit back in.
What to Avoid
Never spray or soak the HEPA filter, even if it looks dirty. Water can cause the fibers to clump and lose efficiency, and mold can grow in damp media. Avoid cleaning agents, which can leave residue that the purifier then circulates into the room.
When to Replace Instead of Clean
Cleaning extends the life of the pre-filter, but it does not restore the HEPA or carbon layers. Replace the full cartridge when the indicator light signals it, when the carbon smells stale even after cleaning the pre-filter, or when airflow noticeably drops. Many owners find that a replacement cycle of roughly six to twelve months works for typical household use, though heavy smoke, pets or high dust loads shorten that window. The Levoit filter-replacement articles on this site cover model-specific intervals in more detail.
Once you install a new filter, reset the change-filter indicator. The steps differ by model, so check the manual or the guide on how to reset your unit.
Recommended gear
- Soft-bristle vacuum brush attachment: Lifts pet hair and dust from the mesh without tearing it. View on Amazon
- Replacement Levoit filters: Keep a spare on hand so the purifier never runs without one while you let the washable pre-filter dry. View on Amazon
- Microfiber drying towel: Absorbs rinse water from the pre-filter so it dries faster and more evenly. View on Amazon
Common Mistakes and Tips
- Cleaning the HEPA filter with water or a vacuum. This damages the media and is the most common error.
- Reinstalling a damp pre-filter. Wait the full drying time to prevent mold.
- Ignoring the replacement indicator because the filter looks clean. Particles can be trapped deep in the media even when the surface appears fine.
- Running the unit with the pre-filter removed. Dust then reaches the HEPA layer and shortens its life.
- Writing down the install date of each new filter so you can track real usage instead of guessing.
FAQ
Can I wash the HEPA filter in my Levoit purifier?
No. True HEPA media is not designed to be washed, and water or cleaning solutions can reduce its ability to capture fine particles. Replace it when the indicator tells you to.
How often should I clean the pre-filter?
Many owners clean the pre-filter every two to four weeks in homes with pets or heavy dust, and less often in cleaner environments. Check it visually and clean whenever it looks visibly coated.
Why does my purifier still smell after cleaning?
Odor usually comes from the activated carbon layer, which becomes saturated over time. Cleaning the pre-filter will not fix this, so replacing the cartridge is the usual solution.
Conclusion
To clean a Levoit air purifier filter properly, wash only the outer pre-filter and let it dry fully before reinstalling it. Keep the HEPA and carbon layers dry and replace them on schedule. If you have a health condition or a persistent problem with air quality, consult a qualified professional for advice specific to your situation.

