Updated November 2026
To reset a Levoit air purifier, you can either clear the filter-change indicator after installing a new filter, or perform a full factory reset to clear settings and reconnect the unit to your Wi-Fi app. Which method you need depends on the problem you are trying to solve. This guide walks through both, along with the checks to run first so you do not reset a unit that just needs a simple fix.
Before You Reset: Identify Your Model and Problem
Levoit makes several lines of purifiers, and the button layout differs between them. Check the label on the back or bottom of the unit for the exact model number before following any instructions. If the purifier is showing a red light, a fault code or a flashing indicator, Levoit Air Purifier Red Light: What It Means and How to Fix It explains what each signal usually means, which can save you a reset you do not need.
Shopping for one? See our guide: Levoit Vital 200S Air Purifier Review (2026): Pros, Cons & Who Should Buy. For a deeper look, How to Do a Weekly Home Reset to Stay Organized covers this in detail.
Most resets fall into one of two categories. A filter reset only clears the timer that tells the unit a filter is due for replacement. A factory reset returns all settings to default, including fan speed presets, timers, auto mode and app pairing. Use the filter reset for routine maintenance and the factory reset only when the unit misbehaves or you are passing it to someone else.
How to Reset the Filter Indicator
Run the filter reset only after you have physically replaced the filter. Resetting the indicator without changing the filter will simply hide the warning while the old filter stays in place.
- Turn the purifier off and unplug it from the outlet.
- Open the rear or side panel and remove the old filter. Install the new filter with the correct orientation, then close the panel.
- Plug the unit back in and press the power button to turn it on.
- Press and hold the filter or reset button (the label varies by model) for about three seconds, until the indicator light changes or the unit beeps.
- Confirm the filter light has turned off. If it has not, power-cycle the unit and try again.
If you are unsure how to reach the filter compartment on your model, Levoit Air Purifier Replace Filter: Step-by-Step Guide (2026) covers the removal process in more detail.
How to Perform a Full Factory Reset
A factory reset clears saved preferences and removes the unit from the Levoit app. Some models do not have a dedicated reset combination, so check your manual first. On many units, the sequence looks like this:
- Unplug the purifier and wait at least 30 seconds so residual power drains.
- Plug it back in while holding the power button, or follow the model-specific combination in the manual (often holding two buttons together).
- Release the buttons when the display or indicator flashes, then wait for the unit to finish its startup sequence.
- Once it powers on in its default state, check that fan speed, mode and timer settings have returned to factory values.
After a factory reset, you will need to re-add the device in the Levoit app. Remove the old entry from the app first to avoid duplicate listings. If the unit will not connect afterward, Levoit Core 300P Air Purifier: Setup, Room Size, and Filter Tips (2026) walks through setup steps that apply across several Core models.
Checking the Unit After Reset
A reset is only useful if the purifier runs properly afterward. Run it on a medium speed for about 15 minutes and listen for unusual noises, which can indicate that the filter or pre-filter is not seated correctly. Check that the air quality indicator responds when you wave your hand near the sensor or light a match outside the room, since that confirms the sensor is active. If the unit still shows a fault after a full factory reset, the problem is likely hardware related and worth raising with Levoit support.
Common Mistakes to Avoid
- Resetting the filter indicator before installing the new filter, which leaves the old filter in use with a false “clean” reading.
- Pressing reset buttons without checking the manual, since holding the wrong combination can trigger a different function.
- Forgetting to remove the purifier from the app before re-adding it, which causes pairing errors.
- Skipping the 30-second power drain, which can leave settings partly intact after a reset.
- Assuming a reset will fix a physical fault; persistent error lights usually need a diagnosis, not another reset.
Recommended Gear
- Replacement filters for your exact model are the most common reason people reset the indicator, so keep a spare on hand. View on Amazon
- A small flashlight helps when locating the filter compartment or reading small button labels on the control panel. View on Amazon
FAQ
Will resetting the filter indicator damage my purifier?
No. The filter reset only changes the internal timer that tracks maintenance reminders. It does not affect the fan, motor or sensors.
Do I lose my Wi-Fi connection after a factory reset?
Yes. A factory reset removes the stored network and app pairing, so you will need to re-add the unit in the Levoit app.
When should I call a professional instead of resetting?
If the unit shows persistent fault codes after a factory reset, emits a burning smell or will not power on, stop using it and contact Levoit support or a qualified appliance technician.
Conclusion
Use the filter reset after every filter change and reserve the factory reset for settings problems or re-pairing. Always check the manual for your exact model, since button combinations vary. If a reset does not resolve the issue, the problem is likely physical and needs further diagnosis.

